UART methods & HA 1.31 support

- Update UART 1 and 2 methods for NeoPixelBus v2.4.1
- HA E1.31 support

Arduino/McLighting/McLighting.ino

@@ -61,7 +61,7 @@
 #ifdef ENABLE_E131
   #include <ESPAsyncUDP.h>         //https://github.com/me-no-dev/ESPAsyncUDP
   #include <ESPAsyncE131.h>        //https://github.com/forkineye/ESPAsyncE131
-  ESPAsyncE131 e131(UNIVERSE_COUNT);
+  ESPAsyncE131 e131(END_UNIVERSE - START_UNIVERSE + 1);
 #endif
 
 
@@ -96,14 +96,18 @@ WS2812FX strip = WS2812FX(NUMLEDS, PIN, NEO_GRB + NEO_KHZ800);
 // and minimize distance between Arduino and first pixel.  Avoid connecting
 // on a live circuit...if you must, connect GND first.
 
-#ifdef USE_WS2812FX_DMA
+#ifdef USE_WS2812FX_DMA // Uses GPIO3/RXD0/RX, more info: https://github.com/Makuna/NeoPixelBus/wiki/ESP8266-NeoMethods
   #include <NeoPixelBus.h>
   NeoEsp8266Dma800KbpsMethod dma = NeoEsp8266Dma800KbpsMethod(NUMLEDS, 3);  //800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
   //NeoEsp8266Dma400KbpsMethod dma = NeoEsp8266Dma400KbpsMethod(NUMLEDS, 3);  //400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
 #endif
-#ifdef USE_WS2812FX_UART
+#ifdef USE_WS2812FX_UART1 // Uses UART1: GPIO1/TXD0/TX, more info: https://github.com/Makuna/NeoPixelBus/wiki/ESP8266-NeoMethods
   #include <NeoPixelBus.h>
-  NeoEsp8266Uart800KbpsMethod dma = NeoEsp8266Uart800KbpsMethod(NUMLEDS, 3);
+  NeoEsp8266Uart0800KbpsMethod dma = NeoEsp8266Uart0800KbpsMethod(NUMLEDS, 3);
+#endif
+#ifdef USE_WS2812FX_UART2 // Uses UART2: GPIO2/TXD1/D4, more info: https://github.com/Makuna/NeoPixelBus/wiki/ESP8266-NeoMethods
+  #include <NeoPixelBus.h>
+  NeoEsp8266Uart1800KbpsMethod dma = NeoEsp8266Uart1800KbpsMethod(NUMLEDS, 3);
 #endif
 #if defined(USE_WS2812FX_DMA) or defined(USE_WS2812FX_UART)
   void DMA_Show(void) {
@@ -925,7 +929,7 @@ void setup() {
   #ifdef ENABLE_E131
   // Choose one to begin listening for E1.31 data
   // if (e131.begin(E131_UNICAST))                             // Listen via Unicast
-  if (e131.begin(E131_MULTICAST, UNIVERSE, UNIVERSE_COUNT)) // Listen via Multicast
+  if (e131.begin(E131_MULTICAST, START_UNIVERSE, END_UNIVERSE)) // Listen via Multicast
       Serial.println(F("Listening for data..."));
   else
       Serial.println(F("*** e131.begin failed ***"));

Arduino/McLighting/definitions.h

@@ -1,5 +1,6 @@
 //#define USE_WS2812FX_DMA      // Uses PIN is ignored & set to RX/GPIO3  Uses WS2812FX, see: https://github.com/kitesurfer1404/WS2812FX
-//#define USE_WS2812FX_UART     // Uses PIN is ignored & set to D4/GPIO2  Uses WS2812FX, see: https://github.com/kitesurfer1404/WS2812FX
+//#define USE_WS2812FX_UART1     // Uses PIN is ignored & set to D4/GPIO2  Uses WS2812FX, see: https://github.com/kitesurfer1404/WS2812FX
+//#define USE_WS2812FX_UART2     // Uses PIN is ignored & set to TX/GPIO1  Uses WS2812FX, see: https://github.com/kitesurfer1404/WS2812FX
 
 // Neopixel
 #define PIN 14           // PIN (14 / D5) where neopixel / WS2811 strip is attached
@@ -20,8 +21,8 @@ const char HOSTNAME[] = "McLighting01";   // Friedly hostname
 #define ENABLE_E131              // E1.31 implementation
 
 #ifdef ENABLE_E131
-  #define UNIVERSE 1                    // First DMX Universe to listen for
+  #define START_UNIVERSE 1                    // First DMX Universe to listen for
-  #define UNIVERSE_COUNT 2              // Total number of Universes to listen for, starting at UNIVERSE
+  #define END_UNIVERSE 2              // Total number of Universes to listen for, starting at UNIVERSE
 #endif
 
 //#define WIFIMGR_PORTAL_TIMEOUT 180

Arduino/McLighting/request_handlers.h

@@ -2,6 +2,8 @@
 // Request handlers
 // ***************************************************************************
 #ifdef ENABLE_E131
+void checkForRequests(void); //prototype
+
 void handleE131(){
   if (!e131.isEmpty())
   {
@@ -11,7 +13,7 @@ void handleE131(){
     uint16_t universe = htons(packet.universe);
     uint8_t *data = packet.property_values + 1;
 
-    if (universe < UNIVERSE || universe > UNIVERSE_COUNT) return; //async will take care about filling the buffer
+    if (universe < START_UNIVERSE || universe > END_UNIVERSE) return; //async will take care about filling the buffer
 
     // Serial.printf("Universe %u / %u Channels | Packet#: %u / Errors: %u / CH1: %u\n",
     //               htons(packet.universe),                 // The Universe for this packet
@@ -20,7 +22,7 @@ void handleE131(){
     //               e131.stats.packet_errors,               // Packet error counter
     //               packet.property_values[1]);             // Dimmer data for Channel 1
 
-    uint16_t multipacketOffset = (universe - UNIVERSE) * 170; //if more than 170 LEDs (510 channels), client will send in next higher universe
+    uint16_t multipacketOffset = (universe - START_UNIVERSE) * 170; //if more than 170 LEDs (510 channels), client will send in next higher universe
     if (NUMLEDS <= multipacketOffset) return;
     uint16_t len = (170 + multipacketOffset > NUMLEDS) ? (NUMLEDS - multipacketOffset) : 170;
     for (uint16_t i = 0; i < len; i++){
@@ -28,6 +30,7 @@ void handleE131(){
       strip.setPixelColor(i + multipacketOffset, data[j], data[j + 1], data[j + 2]);
     }
     strip.show();
+    checkForRequests();
   }
 }
 #endif
@@ -839,7 +842,14 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
 
       //char modeName[30];
       //strncpy_P(modeName, (PGM_P)strip.getModeName(strip.getMode()), sizeof(modeName)); // copy from progmem
+      #if defined(ENABLE_E131) and defined(ENABLE_HOMEASSISTANT)
+      if (mode == E131)
+        root["effect"] = "E131";
+      else
         root["effect"] = strip.getModeName(strip.getMode());
+      #else
+        root["effect"] = strip.getModeName(strip.getMode());
+      #endif
 
       char buffer[measureJson(root) + 1];
       serializeJson(root, buffer, sizeof(buffer));
@@ -918,6 +928,13 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
         String effectString = root["effect"].as<String>();
 
         for (uint8_t i = 0; i < strip.getModeCount(); i++) {
+          #if defined(ENABLE_E131) and defined(ENABLE_HOMEASSISTANT)
+          if(effectString == "E131"){
+            if(strip.isRunning()) strip.stop();
+            mode = E131;
+            break;
+          }
+          #endif
           if(String(strip.getModeName(i)) == effectString) {
             mode = SET_MODE;
             ws2812fx_mode = i;
@@ -1012,6 +1029,9 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
             for (uint8_t i = 0; i < strip.getModeCount(); i++) {
               effect_list.add(strip.getModeName(i));
             }
+            #if defined(ENABLE_E131) and defined(MQTT_HOME_ASSISTANT_SUPPORT)
+              effect_list.add("E131");
+            #endif
             char buffer[measureJson(json) + 1];
             serializeJson(json, buffer, sizeof(buffer));
             mqtt_client.publish(String("homeassistant/light/" + String(HOSTNAME) + "/config").c_str(), buffer, true);
@@ -1096,6 +1116,9 @@ void webSocketEvent(uint8_t num, WStype_t type, uint8_t * payload, size_t lenght
           for (uint8_t i = 0; i < strip.getModeCount(); i++) {
             effect_list.add(strip.getModeName(i));
           }
+          #if defined(ENABLE_E131) and defined(MQTT_HOME_ASSISTANT_SUPPORT)
+            effect_list.add("E131");
+          #endif
           char buffer[measureJson(json) + 1];
           serializeJson(json, buffer, sizeof(buffer));
           DBG_OUTPUT_PORT.println(buffer);

clients/HomeAssistant/light.yaml

@@ -63,6 +63,7 @@ light:
       - "Bicolor Chase"
       - "Tricolor Chase"
       - "ICU"
+      - "E131"
     brightness: true
     color_temp: true
     rgb: true
@@ -79,7 +80,7 @@ input_number:
     step: 5
     
 automation:
-  - id: 71938579813759813757
+  - id: "71938579813759813757"
     alias: NeoPixel Animation Speed Send
     initial_state: true
     hide_entity: false
@@ -93,7 +94,7 @@ automation:
         topic: home/McLighting01_ha/state/in
       service: mqtt.publish
 
-  - id: 93786598732698756967
+  - id: "93786598732698756967"
     alias: NeoPixel Animation Speed Receive
     trigger:
     - platform: mqtt

platformio.ini

@@ -51,7 +51,7 @@ lib_deps =
   AsyncMqttClient
   https://github.com/bblanchon/ArduinoJson.git#v6.7.0-beta
   WS2812FX
-  NeoPixelBus
+  NeoPixelBus@2.4.1
   WebSockets
   ESPAsyncE131
   ESPAsyncUDP