overworked readme
This commit is contained in:
Bernhard Kubicek
parent
e87df99e22
commit
61e0740bf0
1 changed files with 117 additions and 9 deletions
126
README.md
126
README.md
|
|
@ -8,8 +8,9 @@ This RepRap firmware is a mashup between <a href="https://github.com/kliment/Spr
|
|||
Derived from Sprinter and Grbl by Erik van der Zalm.
|
||||
Sprinters lead developers are Kliment and caru.
|
||||
Grbls lead developer is Simen Svale Skogsrud.
|
||||
Some features have been added by and configuration has been added by:
|
||||
Bernhard Kubicek, Matthijs Keuper, Bradley Feldman, and others...
|
||||
A fork by bkubicek for the Ultimaker was merged, and further development was aided by him.
|
||||
Some features have been added by:
|
||||
Lampmaker, Bradley Feldman, and others...
|
||||
|
||||
|
||||
Features:
|
||||
|
|
@ -20,33 +21,140 @@ Features:
|
|||
- preliminary support for Matthew Roberts advance algorithm
|
||||
For more info see: http://reprap.org/pipermail/reprap-dev/2011-May/003323.html
|
||||
- Full endstop support
|
||||
- Simple LCD support (16x2)
|
||||
- SD Card support
|
||||
- Provisions for Bernhard Kubicek's new hardware control console and 20x4 lcd
|
||||
- SD Card folders (works in pronterface)
|
||||
- LCD support (ideally 20x4)
|
||||
- LCD menu system for autonomous SD card printing, controlled by an click-encoder.
|
||||
- EEPROM storage of e.g. max-velocity, max-acceleration, and similar variables
|
||||
- many small but handy things originating from bkubicek's fork.
|
||||
- Arc support
|
||||
- Temperature oversampling
|
||||
- Dynamic Temperature setpointing aka "AutoTemp"
|
||||
- Support for QTMarlin, a very beta GUI for PID-tuning and velocity-acceleration testing. https://github.com/bkubicek/QTMarlin
|
||||
- Endstop trigger reporting to the host software.
|
||||
- Updated sdcardlib
|
||||
- Heater power reporting. Useful for PID monitoring.
|
||||
|
||||
This firmware is optimized for Ultimaker's gen6 electronics (including the Ultimaker 1.5.x daughterboard and Arduino Mega 2560).
|
||||
|
||||
The default baudrate is 115200.
|
||||
The default baudrate is 250000. This baudrate has less jitter and hence errors than the usual 115200 baud, but is less supported by drivers and host-environments.
|
||||
|
||||
|
||||
========================================================================================
|
||||
Differences and additions to the already good Sprinter firmware:
|
||||
|
||||
Look-ahead:
|
||||
Marlin has look-ahead. While sprinter has to break and re-accelerate at each corner,
|
||||
lookahead will only decelerate and accelerate to a velocity,
|
||||
so that the change in vectorial velocity magnitude is less than the xy_jerk_velocity.
|
||||
This is only possible, if some future moves are already processed, hence the name.
|
||||
It leads to less over-deposition at corners, especially at flat angles.
|
||||
|
||||
Arc support:
|
||||
Splic3r can find curves that, although broken into segments, were ment to describe an arc.
|
||||
Marlin is able to print those arcs. The advantage is the firmware can choose the resolution,
|
||||
and can perform the arc with nearly constant velocity, resulting in a nice finish.
|
||||
Also, less serial communication is needed.
|
||||
|
||||
Temperature Oversampling:
|
||||
To reduce noise and make the PID-differential term more useful, 16 ADC conversion results are averaged.
|
||||
|
||||
AutoTemp:
|
||||
If your gcode contains a wide spread of extruder velocities, or you realtime change the building speed, the temperature should be changed accordingly.
|
||||
Usually, higher speed requires higher temperature.
|
||||
This can now be performed by the AutoTemp function
|
||||
By calling M109 S<mintemp> T<maxtemp> F<factor> you enter the autotemp mode.
|
||||
You can leave it by calling M109 without any F.
|
||||
If active, the maximal extruder stepper rate of all buffered moves will be calculated, and named "maxerate" [steps/sec].
|
||||
The wanted temperature then will be set to t=tempmin+factor*maxerate, while being limited between tempmin and tempmax.
|
||||
If the target temperature is set manually or by gcode to a value less then tempmin, it will be kept without change.
|
||||
Ideally, your gcode can be completely free of temperature controls, apart from a M109 S T F in the start.gcode, and a M109 S0 in the end.gcode.
|
||||
|
||||
EEPROM:
|
||||
If you know your PID values, the acceleration and max-velocities of your unique machine, you can set them, and finally store them in the EEPROM.
|
||||
After each reboot, it will magically load them from EEPROM, independent what your Configuration.h says.
|
||||
|
||||
LCD Menu:
|
||||
If your hardware supports it, you can build yourself a LCD-CardReader+Click+encoder combination. It will enable you to realtime tune temperatures,
|
||||
accelerations, velocities, flow rates, select and print files from the SD card, preheat, disable the steppers, and do other fancy stuff.
|
||||
One working hardware is documented here: http://www.thingiverse.com/thing:12663
|
||||
Also, with just a 20x4 or 16x2 display, useful data is shown.
|
||||
|
||||
SD card folders:
|
||||
If you have an SD card reader attached to your controller, also folders work now. Listing the files in pronterface will show "/path/subpath/file.g".
|
||||
You can write to file in a subfolder by specifying a similar text using small letters in the path.
|
||||
Also, backup copies of various operating systems are hidden, as well as files not ending with ".g".
|
||||
|
||||
Endstop trigger reporting:
|
||||
If an endstop is hit while moving towards the endstop, the location at which the firmware thinks that the endstop was triggered is outputed on the serial port.
|
||||
This is useful, because the user gets a warning message.
|
||||
However, also tools like QTMarlin can use this for finding acceptable combinations of velocity+acceleration.
|
||||
|
||||
Coding paradigm:
|
||||
Not relevant from a user side, but Marlin was split into thematic junks, and has tried to partially enforced private variables.
|
||||
This is intended to make it clearer, what interacts which what, and leads to a higher level of modularization.
|
||||
We think that this is a useful prestep for porting this firmware to e.g. an ARM platform in the future.
|
||||
A lot of RAM (with enabled LCD ~2200 bytes) was saved by storing char []="some message" in Program memory.
|
||||
In the serial communication, a #define based level of abstraction was enforced, so that it is clear that
|
||||
some transfer is information (usually beginning with "echo:"), an error "error:", or just normal protocol,
|
||||
necessary for backwards compatibility.
|
||||
|
||||
Interrupt based temperature measurements:
|
||||
An interrupt is used to manage ADC conversions, and enforce checking for critical temperatures.
|
||||
This leads to less blocking in the heater management routine.
|
||||
|
||||
========================================================================================
|
||||
Non-standard M-Codes, different to an old version of sprinter:
|
||||
|
||||
G2 - CW ARC
|
||||
G3 - CCW ARC
|
||||
|
||||
General:
|
||||
M17 - Enable/Power all stepper motors
|
||||
M18 - Disable all stepper motors; same as M84
|
||||
M30 - Print time since last M109 or SD card start to serial
|
||||
M42 - Change pin status via gcode
|
||||
M80 - Turn on Power Supply
|
||||
M81 - Turn off Power Supply
|
||||
M114 - Output current position to serial port
|
||||
M119 - Output Endstop status to serial port
|
||||
Movement variables:
|
||||
M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000) Unused in Marlin!!
|
||||
M203 - Set maximum feedrate that your machine can sustain (M203 X200 Y200 Z300 E10000) in mm/sec
|
||||
M204 - Set default acceleration: S normal moves T filament only moves (M204 S3000 T7000) im mm/sec^2 also sets minimum segment time in ms (B20000) to prevent buffer underruns and M20 minimum feedrate
|
||||
M220 - set build speed factor override percentage S:factor in percent ; aka "realtime tuneing in the gcode"
|
||||
M301 - Set PID parameters P I and D
|
||||
M400 - Finish all moves
|
||||
|
||||
Advance:
|
||||
M200 - Set filament diameter for advance
|
||||
M205 - advanced settings: minimum travel speed S=while printing T=travel only, B=minimum segment time X= maximum xy jerk, Z=maximum Z jerk
|
||||
|
||||
EEPROM:
|
||||
M500 - stores paramters in EEPROM
|
||||
M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
========================================================================================
|
||||
|
||||
|
||||
|
||||
Configuring and compilation
|
||||
|
||||
|
||||
Install the latest arduino software IDE/toolset (currently 0022)
|
||||
Install the arduino software IDE/toolset v22
|
||||
http://www.arduino.cc/en/Main/Software
|
||||
|
||||
Install Ultimaker's RepG 25 build
|
||||
http://software.ultimaker.com
|
||||
(or alternatively install Kliment's printrun/pronterface https://github.com/kliment/Printrun_)
|
||||
For SD handling and as better substitute (apart from stl manipulation) download
|
||||
the very nice Kliment's printrun/pronterface https://github.com/kliment/Printrun
|
||||
|
||||
Copy the Ultimaker Marlin firmware
|
||||
https:/github.com/bkubicek/Marlin
|
||||
https://github.com/ErikZalm/Marlin/tree/Marlin_v1
|
||||
(Use the download button)
|
||||
|
||||
Start the arduino IDE.
|
||||
Select Tools -> Board -> Arduino Mega 2560
|
||||
Select Tools -> Board -> Arduino Mega 2560 or your microcontroller
|
||||
Select the correct serial port in Tools ->Serial Port
|
||||
Open Marlin.pde
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue